 Charging
the Phone
To charge your phone, simply plug one end of your power supply into
the base of the phone and plug the other end into an electrical outlet
(100~240V).
The battery strength indicator in the upper right of the display
scrolls when the phone is properly charging. When the phone is fully
charged and the phone is powered off, the message Fully
Charged! appears on the display. The battery fully charges
in about 2 - 3 hours.
A fully charged phone has about 3 hours of talk time. Standby time
lasts for about 40 - 80 hours.
Note: It is normal for the battery
and charger to be warm during charging.
Switching the Phone On/Off
Switch the phone on and enter standby mode by pressing and holding
the Power key. An animation appears when you are successful. Switch
the phone off by pressing and holding the Power key. The display
is blank when you are successful.
Associate and Register Your Phone:
To use your BroadVoice WiFi phone, you must turn it on, associate
the phone with an access point (AP) and register the phone with
BroadVoice. Once this process is completed, you can immediately
start making calls. In most cases, when you turn the unit on for
the first time, this whole process takes place automatically in
a very short time. If you have turned on the phone and the phone
display’s screen saver image appears, then the phone has
successfully associated with an AP, obtained an IP address and
registered with BroadVoice, and you can start using the phone.
Otherwise, you will have to perform a Wireless
Scan.
To associate and register your phone, follow
these steps:
- Power up your computer network, including your cable/DSL modem
and your Access Point/router.
- Turn on your phone by holding the Power key for a few seconds.
- You phone will initially display “Connecting
to…” and will scan for an available AP.
- You phone will next display “Registering
to…” after it makes a network connection.
- If the phone beeps once and its screen saver imageappears on
the LCD, the phone has successfully associated with an AP, obtained
an IP address and registered with BroadVoice.
You can use your phone immediately if you have successfully received
this message.
- If the phone has not successfully registered, then do a wireless
scan and configure Static IP (DHCP) as
necessary.
- For more information on these procedures, see Scanning
for an Access Point (AP) and Configuring
for Static IP (DHCP) .
Wireless
Scan: Scanning for an Access Point (AP)
NOTE: You
only need to perform a wireless scan if your phone did not
successfully register.
The Net Search feature enables you to select and associate
your BroadVoice WiFi VoIP Phone with your network AP, obtain
an IP address, and register the phone with BroadVoice service.
To do a wireless scan, follow these steps:
- Use the left soft key to select Menu.
- Use the Navigation key to scroll to WiFi-Settings and
select ‘OK’ using the
left soft key.
- Use your Navigation key to scroll to Net
Search and select ‘OK’ using
the left soft key.
- The phone searches for APs in your network and lists the
SSIDs of each SSID.
- Highlight the appropriate AP and then use the left soft
key to select the Save option.
- Four options will display for storing your AP's SSID. Highlight
one of the four SSID locations and select Save.
A status message (Ok) will display which indicates the success
of the operation.
- Highlight the appropriate encryption bit setting and then
select ‘OK’ by pressing the left
soft key. Select ‘Null’ if
your AP does not use any wireless encryption. A status message
(Ok) will display which
indicates the success of the operation.
- Select Exit by pressing
the right soft key.
- Press Exit again until
you return to the main menu.
- The phone will display “Connecting
to [SSID]”. Once it properly connects with
your AP the phone will then display “Registering
via [SSID]”.
- A few moments later, when your F1000 phone becomes fully
registered on the BroadVoice network, it will beep once and
display its screen saver.
|
|
Installation
of the BroadVoice WiFi VoIP Phone
What's
included:
